 Specifications Installation
Manual
Sales Brochure
Données Et Spécifications Des Produits
Aussi disponible
en français
Datos Del Producto Y Especificaciones
También
disponible en español
The
KVS/KVD features single or dual compressor(s) and a vertical
discharge air-cooled condenser that is suitable for large
walk-in coolers and freezers, blast freezers, warehouse applications
and air conditioned spaces where roof mounted condensers are
most practical. Using high efficiency compressors and utilizing
the THERMOSPAN™ condenser core design, the unit meets
all application needs from 15 to 100 Hp (air conditioning,
high and medium temperature) and 10 to 80 Hp (low temperature).
Applications
- Refrigeration:
•
Models available from 10 - 80 HP
• Low Temperature
• R22
• Dual or Single Compressor
Applications
- Air Conditioning:
•
Models available from 15 - 100 HP
• Air Conditioning, High & Med. Temperature
• R22, R404A, R507
• Dual or Single Compressor
General
Features:
•
Energy Efficient Compressors with POE Oil. Several Options
to Choose from: Copeland, Discus, Bitzer Reciprocating,
Carlyle Reciprocating, Copeland Screw.
• Single, Dual and Parallel-piped (optional) Compressor Configurations
Available.
• Thermospan™ Condenser Core Design Eliminates
Tube Sheet Leaks and Provides Reliable Operation
• 3/8” Condenser Tubes Reduce Refrigerant Charge
• Generously Sized Condenser Allows Unit To Operate
at Higher Than Normal Ambient Conditions
• Optional Coating and Fin Surfaces for Condenser
Core Protection Available
• Specially Designed, Thermally Protected and Permanently
Lubricated Ball Bearing Condenser Fan Motor(s)
• Receivers are Liberally Sized and Include Inlet
as well as Outlet Service Valves
• Subcooling Circuit in Condenser on All Models (except
H2 & A2) Increases Overall System Efficiency and Provides Dependable
Compressor Operation
• Utilizes Pre-Formed Internal Piping, Eliminates
Welded Joints and Reduces Chances of a Leak
• Electrical Components are Housed In A Spacious and
Conveniently Located Panel. In case of a Compressor
Trip, a Lock-out Relay
De-energizes the Liquid Solenoid
Valve. In Addition, SPDT Contact is Provided
for Field Wired Alarm Circuit
• End Compartment Panels Allow Unrestricted Access
to Service The Compressor(s) and All Other Components
• Raceway for Pressure Control Wiring and Connections Provides
Neat Appearance
• Units are Available with Energy Efficient Thermosaver™
Hot Gas Defrost Option
• Units are Environmentally Friendly, Operating on
Less Power and Refrigerant Charge
Standard
Features:
Refrigeration
• Spring Mounted Compressor with Discharge Vibrasorber
• Compressor Head Cooling Fans On Low Temperature
Models
• Compressor Crankcase Heater
• Flexible Hose on All Compressor Pressure Control
Connections
• Two Valve Adjustable (Pre-Set at Factory) Low Ambient
Head Pressure Control
• Condenser Fan Cycling Control (Pressure) On Two-Fan
Models and Up
• Fused Condenser Fan Motors
• Receiver Inlet/Outlet Valves and Safety Pressure
Relief Valve
• Replaceable Liquid Line Drier and Sight Glass
• Anti-Short Cycle Time Delay Relay
• Oil Failure Control (Non-Electronic)
• Discharge Line Thermostat
• Separate HP and LP Compressor Controls
• Part-Winding Start on All 30 HP and up, Operating
on 208/230V-3ph
• Lock-Out Relay
• Sub-Cooling Circuit on Medium and Low Temperature
Unit
Air
Conditioning
•
Spring Mounted Compressor with Discharge Vibrasorber
• Compressor Crankcase Heater
• Condenser Fan Cycling Control (Pressure) On Two-Fan
Models and Up
• Fused Condenser Fan Motors
• Part-Winding Start on All 30 HP and up, Operating
on 208/230V-3ph
Optional
Features (Factory Mounted):
•
Suction Line Vibration Eliminator
• Suction Accumulator (with or without Heat Exchanger)
• Replaceable Suction Filter
• Insulated Suction Lines
• Crankcase Pressure Regulating Valve
• Compressor Capacity Control (Cylinder Unloading
on 4D-6D-6F Compressors or “Moduload” on 3D
Compressors)
• Discharge Line Check Valve
• Hot Gas Bypass Tees / Regulating Valves / De superheating
TXV
• Oil Separator • Oversized Condenser
• Oversized Receiver • Heated and Insulated
Receiver
• ThermosaverTM Hot Gas Defrost • Disconnect
Switch (Fused or Non-Fused)
• Compressor Circuit Breaker • Electronic Oil
Failure Control
• Voltage / Phase Monitor • Defrost Time Clock
• Part-winding Start (standard on 30HP and up operating
on
208/230-3)
• Defrost Heater / Evaporator Fan Contactors with
Fuse Block
• Single Point Electrical Hook Up for Evaporator and
Controls
|
